Difference between revisions of "Simulating Verilog"

From Vlsiwiki
Jump to: navigation, search
(VCS)
(VCS)
 
(9 intermediate revisions by 2 users not shown)
Line 43: Line 43:
 
  ./simv
 
  ./simv
  
Specifying -R on the command line will run it immediately and not produce the simv binary.
+
Specifying -R on the command line will run it immediately and not produce the simv binary. Specifying -gui on the command line will load the SimVision GUI. On 64-bit machines, you may get an error message like this:
  
Specifying -gui on the command line will load the SimVision GUI.
+
    Error: DVE in 64Bit mode requires a special license.
 +
    For more details, please contact Synopsys VCS Support.
  
To avoid getting an error message like this:
+
To avoid this, you must load the simulation in dve (the GUI) manually like this:
Error: DVE in 64Bit mode requires a special license.
+
      For more details, please contact Synopsys VCS Support.
+
 
+
use the following:
+
export VCS_ARCH_OVERRIDE=""
+
 
+
vcs +v2k -gui -f sat.f
+
 
+
dve
+
 
+
 
+
, where sat.f is a file holding the list of your verilog files.
+
  
 +
    export VCS_ARCH_OVERRIDE="redhat72"
 +
    vcs +v2k -gui -f project.f
 +
    export VCS_ARCH_OVERRIDE=""
 +
    dve
  
 
Then, go to Simulator->Setup and select the simulator executable.
 
Then, go to Simulator->Setup and select the simulator executable.

Latest revision as of 00:18, 15 May 2008

Introduction

This section will briefly talk about how to simulate Verilog. You can simulate Verilog that is either behavioral, gate-level, or back-annotated (with delays). Behavioral and gate-level are done in the same way, but back annotate requires an extra system call in your Verilog.

The first thing I recommend that you do is to create a "project.f" file that is just a list of all of your Verilog files. Like this:

sram.v
sram_tb.v

Running Verilog

You can use three different Verilog simulators: ncverilog ("ncverilog"), VCS ("vcs") or verilog-XL ("verilog"). There is also a 4th GNU simulator called Icarus Verilog that you can install on your own computer.

ncverilog

Simply run:

ncverilog -f project.f

Look for any warnings or errors. At the end of the output, you should see:

Simulation complete via $finish(1) at time 10 US + 0
./sram_tb.v:64 	$finish();
ncsim> exit


If you want to view the outputs in a GUI, you can run:

ncverilog -f project.f +gui

or

ncverilog -f project.f +gui +access+rwc   //This will solve problems if there is an error about read access

This will compile the verilog and run SimVision. There is more on SimVision in the Advanced Testbenches tutorial.

You can also put these extra arguments in the project.f file.

VCS

To run VCS:

vcs +v2k -f project.f
./simv

Specifying -R on the command line will run it immediately and not produce the simv binary. Specifying -gui on the command line will load the SimVision GUI. On 64-bit machines, you may get an error message like this:

    Error: DVE in 64Bit mode requires a special license.
    For more details, please contact Synopsys VCS Support.

To avoid this, you must load the simulation in dve (the GUI) manually like this:

    export VCS_ARCH_OVERRIDE="redhat72"
    vcs +v2k -gui -f project.f
    export VCS_ARCH_OVERRIDE=""
    dve

Then, go to Simulator->Setup and select the simulator executable.

Verilog-XL

Verilog-XL does not support much of Verilog 2001. However, given that, it can be run in the same way:

verilog -f project.f

or:

verilog -f project.f +gui

Icarus Verilog

Icarus can be run like this:

iverilog -c project.f

Note that this will *compile* the verilog into a binary called "a.out". To actually run the Verilog, you must now run it:

./a.out

Icarus Verilog seems to be more lenient on errors in Verilog code. You should make sure it compiles in NCVerilog too. Icarus does not come with a GUI, so you will either need to use the $display command or install GTKWave.

Simulating Verilog in Ultrasim

For non-digital simulations, you can simulate a structural Verilog netlist in Ultrasim as well. However, you need to supply the spice subcircuits of the library:

/mada/software/techfiles/osu_soc_v2.7/cadence/lib/tsmc025/signalstorm/osu025_stdcells.sp

See more in the Analog/Mixed Signal section.

Saving a VCD

Some waveform viewers and other tools accept VCD as an input. A VCD file is a vector change dump. It simply has some or all of the signal changes over the entire simulation time. You can dump a VCD file from your simulation using:

initial begin
  $dumpvars(0,topmodule); 
  $dumpfile("mydump.vcd");
end

The 0 specifies the number of levels to dump. 0 is a shortcut for all levels whereas 4 would just mean 4 hierarchical levels down from topmodule. The arguments to dumpvars are optional. By default it dumps the current module only, I believe.

Assertions

ncverilog supports PSL assertions with the +assert option. All of the simulators can be used with the OVL assertion library. Tutorials on both PSL and OVL are available on ASIC World.

Back-Annotation

In order to back-annotate, you should output an SDF file from either Synopsys Design Compiler (before physical design) or from SoC encounter. Each SDF format is sometimes different, so you may have to hack it to get it to work. Common incompatibilities are the dilimiting characters in hierarchical names, for example. Carefully watch the warnings!

The system call to back-annotate is like this:

initial begin
  $sdf_annotate("gate/lfsr-final.sdf", l0);
end

where lfsr.sdf is the SDF file and l0 is the instance name of the top module that you synthesized. Note that you should not be using your unsynthesized verilog now. Use the output from synthesis in the file, gate/lfsr-final.v, along with your original testbench.